Introduction: bath cleaning must not be hard to hard to soft to overcome hard

Introduction: bath cleaning must not be hard to hard to soft to overcome hard


In the face of tedious things, the first feeling of stubborn relatives may be hard hitting, but in fact, this often has a negative effect. What we need to do is to avoid its sharp edge and think about the strategy. So how to clean and maintain the non ordinary hard bathtub? It's easy and labor-saving to use soft and hard cotton cloth. It's hard not to do it with half the effort.


1. When cleaning the acrylic bathtub every week, sponge or flannelette should be used. Do not use coarse cloth or cleaning cloth. Do not use any cleaning agent containing granular objects. It is better to avoid direct sunlight and high temperature cigarette butts.

Use mild detergent (such as dishwasher detergent), do not use abrasive detergent. Acrylic bathtubs can also be cleaned with glass water. Cast iron bathtubs should be fully washed with clean water after each use and dried with soft cloth. In case of stubborn stains, use a small amount of abrasive cleaning agent for cleaning. Clean the anti slip surface at the bottom with a soft nylon brush. Do not use wire ball, wire brush or grinding sponge


Wash the Jacuzzi system more than twice a month. Adjust the nozzle clockwise to the fully closed position to prevent air leakage.


Fill the tub with warm water to 2 inches above the maximum nozzle, or leave the water in the tub after use. Add two teaspoons of low foamed powdered automatic dish detergent and a small amount of household bleach in water. Turn on the Jacuzzi for 5 to 10 minutes, then turn it off, drain off the water, and then rinse the surface of the Jacuzzi with water. When the bathtub is in hot and humid state for a long time, many bacteria will grow. Sometimes after cleaning, the surface looks clean. In fact, there are still many bacteria. It is recommended to wipe the surface of the bathtub with boiled water regularly, and do not use disinfectant casually, because the disinfectant may not kill mold and fungus.


2. The surface stains can be washed with the waste soft toothbrush dipped in bleaching powder water, which can not only remove the stains, but also eliminate the mold.

For the stains that are hard to wipe, you can use half a lemon dipped in salt to wipe, or you can use a soft toothbrush to brush with a whitening toothpaste. Turpentine is also very good at this time. For the scale, the products used to clean the toilet are easy to use. If you don't like the pungent taste, you can use lemon and white vinegar as a natural way. Do not use detergent with fading function, especially when the bathtub at home is colored. For mold and fungus causing bacteria, rinse with bleach and peroxide water and dry immediately.


3. Repair the wound in time. Do not move the bathtub without permission. If you need to move the location, you must contact a professional. Do not knock or hit the surface with hard objects, causing bruises or scratches.

If the dark or scratched part of acrylic bathtub needs to be repaired, clean cloth can be used to mix with colorless automatic grinding solution to wipe it hard, and then a layer of colorless protective wax can be applied. Do not wax the area where the feet fall to prevent slipping.


4. Handle the pipe blockage at any time and disinfect the pipe on time once or twice a week to remove the smell and prevent the growth of bacteria.

Can use the product that cleans the sewer specially, pour into the sewer, clean after 5 minutes, pay attention not to use in the metal pipe. If the bathtub is blocked, close the water drain valve first, and then put a proper amount of tap water in the bathtub; place the rubber suction device (used to dredge the toilet) on the water drain valve; when opening the water drain valve, cover the overflow hole of the basin or bathtub; then quickly attract up and down, suck out the dirt or hair, and clean up in time. In case of serious blockage, it can be repeated several times until it is cleared.